gq 129 gq-relays ultra-small package flat polarized relay 7.20 0.3 .283 .012 10.60 0.3 .417 .012 5.20 0.2 .205 .008 10.60 0.3 .417 .012 max.5.40 .213 7.20 0.3 .283 .012 mm inch features ? compact ?at body saves space with a small footprint of 10.6 mm (l) 7.2 mm (w) .417 inch (l) .283 inch (w) for space savings, it also has a very short height of 5.2 mm .205 inch . (standard pc board type.) ? outstanding surge resistance. surge withstand between open contacts: 1,500 v 10 160 m s (fcc part 68) surge withstand between contacts and coil: 2,500 v 2 10 m s (bellcore) ? the use of twin crossbar contacts en- sures high contact reliability. agpd contact is used because of its good sul?de resistance. adopting low-gas molding material. coil assembly molding technology which avoids generating vola- tile gas from coil. ? increased packaging density due to highly ef?cient magnetic circuit de- sign, leakage ?ux is reduced and changes in electrical characteristics from compo- nents being mounted close-together are minimized. this all means a packaging density higher than ever before. ? nominal operating power: 140 mw ? outstanding vibration and shock re- sistance. functional shock resistance: 750 m/s 2 {75g} destructive shock resistance: 1,000 m/s 2 {100g} functional vibration resistance: 10 to 55 hz (at double amplitude of 3.3 mm .130 inch ) destructive vibration resistance: 10 to 55 hz (at double amplitude of 5 mm .197 inch ) specifications contact remarks: * speci?cations will vary with foreign standards certi?cation ratings. * 1 measurement at same location as "initial breakdown voltage" section. * 2 detection current: 10ma. * 3 nominal voltage applied to the coil, excluding contact bounce time. * 4 by resistive method, nominal voltage applied to the coil; contact carrying current: 1 a. * 5 half-wave pulse of sine wave: 6 ms;detection time: 10 m s. * 6 half-wave pulse of sine wave: 6 ms. * 7 detection time: 10 m s . * 8 refer to 5. conditions for operation, transport and storage mentioned in ambient environment (page 61) characteristics notes: g 1 this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. g 2 the upper limit for the ambient temperature is the maximum temperature that can satisfy the coil temperature rise. under the packing condition, allowable temperature range is from C40 to +70 c C40 to +158 f . arrangement 2 form c initial contact resistance, max. (by voltage drop 6 v dc 1a ) 100 m w contact material stationary: agpd+au clad movable: agpd rating nominal switching capacity (resistive load) 1 a 30 v dc 0.3 a 125 v ac max. switching power (resistive load) 30 w, 37.5 v a max. switching voltage 110 v dc, 125 v ac max. switching current 1 a min. switching capacity g 1 10 m a 10 mv dc nominal operating power single side stable 140mw (1.5 to 12 v dc) 230mw (24 v dc) 1 coil latching 100mw (1.5 to 12 v dc) 120mw (24 v dc) expected life (min. operations) mechanical (at 180 cpm) 5 10 7 electrical (at 20 cpm) 1 a 30 v dc resistive 10 5 0.3 a 125 v ac resistive 10 5 initial insulation resistance* 1 min. 1,000m w (at 500v dc) initial breakdown voltage* 2 between open contacts 750 vrms for 1min. between contact sets 1,000 vrms for 1min. between contacts and coil 1,500 vrms for 1min. initial surge voltage between open contacts (10 160 m s) 1,500 v(fcc part 68) between contacts and coil (2 10 m s) 2,500 v(bellcore) operate time [set time]* 3 (at 20 c) max. 4 ms (approx. 2 ms) [max. 4 ms (approx. 2 ms)] release time (without diode) [reset time]* 3 (at 20 c) max. 4 ms (approx. 1 ms) [max. 4 ms (approx. 2 ms)] temperature rise* 4 (at 20 c) max. 50 c shock resistance functional* 5 min. 750 m/s 2 {75g] destructive* 6 min. 1,000 m/s 2 {100g] vibration resistance functional* 7 10 to 55 hz at double amplitude of 3.3 mm destructive 10 to 55 hz at double amplitude of 5 mm conditions for opera- tion, transport and storage* 8 (not freezing and con- densing at low tem- perature) ambient temperature g 2 C40 c to 85 c C40 f to 185 f humidity 5 to 85% r.h. unit weight approx. 1 g .035 oz testing
gq 130 typical applications ? telephone exchange, transmission equipment ? communications devices ? measurement devices ? home appliances, and audio/visual equipment ? handheld and portable products ordering information 200a z 1h ex. agq contact arrangement terminal shape operating function packing style coil voltage (dc) nil: standard pc board terminal a: surface-mount terminal a type s: surface-mount terminal s type 2: 2 form c 0: single side stable 1: 1 coil latching type of operation 0: standard type (b.b.m.) nil: tube packing z: tape and reel packing (piked from 5/6/7/8 pin side) 1h: 1.5v 03 : 3v 4h: 4.5v 06 : 6v 09 : 9v 12 : 12v 24 : 24v note: tape and reel packing symbol ?z?is not marked on the relay. ??type tape and reel packing (picked from 1/2/3/4-pin sid e) is also available. suffix ??instead of ?? types and coil data (at 20 c 68 f ) (1) standard pc board terminal 1) standard packing: 50 pcs. in an inner package (tube); 1,000 pcs. in an outer package 2) speci?ed value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. (2) surface-mount terminal m : for each surface-mounted terminal variation, input the following letter. a type: a , s type: s 1) standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in a n outer package 2) speci?ed value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. operating function part no. coil rating, v dc pick-up volt- age, v dc (max.) (initial) drop-out voltage, v dc (min.) (initial) nominal operating current, ma ( 10%) coil resistance, w ( 10%) nominal operating power, mw max. allowable voltage, v dc standard pc board terminal single side stable agq2001h 1.5 1.13 0.15 93.8 16 140 2.25 agq20003 3 2.25 0.3 46.7 64.2 140 4.5 agq2004h 4.5 3.38 0.45 31 145 140 6.75 agq20006 6 4.5 0.6 23.3 257 140 9 agq20009 9 6.75 0.9 15.5 579 140 13.5 agq20012 12 9 1.2 11.7 1,028 140 18 agq20024 24 18 2.4 9.6 2,504 230 28.8 operating function part no. coil rating, v dc set voltage, v dc (max.) (initial) reset voltage, v dc (max.) (initial) nominal operating current, ma ( 10%) coil resistance, w ( 10%) nominal operating power, mw max. allowable voltage, v dc standard pc board terminal 1 coil latching agq2101h 1.5 1.13 1.13 66.7 22.5 100 2.25 agq21003 3 2.25 2.25 33.3 90 100 4.5 agq2104h 4.5 3.38 3.38 22.2 202.5 100 6.75 agq21006 6 4.5 4.5 16.7 360 100 9 agq21009 9 6.75 6.75 11.1 810 100 13.5 agq21012 12 9 9 8.3 1,440 100 18 agq21024 24 18 18 5.0 4,800 120 36 operating function part no. coil rating, v dc pick-up voltage, v dc (max.) (initial) drop-out voltage, v dc (min.) (initial) nominal operating current, ma ( 10%) coil resistance, w ( 10%) nominal operating power, mw max. allowable voltage, v dc tube packing tape and reel packing single side stable agq200 m 1h agq200 m 1hz 1.5 1.13 0.15 93.8 16 140 2.25 agq200 m 03 agq200 m 03z 3 2.25 0.3 46.7 64.2 140 4.5 agq200 m 4h agq200 m 4hz 4.5 3.38 0.45 31 145 140 6.75 agq200 m 06 agq200 m 06z 6 4.5 0.6 23.3 257 140 9 agq200 m 09 agq200 m 09z 9 6.75 0.9 15.5 579 140 13.5 agq200 m 12 agq200 m 12z 12 9 1.2 11.7 1,028 140 18 agq200 m 24 agq200 m 24z 24 18 2.4 9.6 2,504 230 28.8
gq 131 m : for each surface-mounted terminal variation, input the following letter. a type: a , s type: s 1) standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in a n outer package 2) speci?ed value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. operating function part no. coil rating, v dc set voltage, v dc (max.) (initial) reset voltage, v dc (max.) (initial) nominal operating current, ma ( 10%) coil resistance, w ( 10%) nominal operating power, mw max. allowable voltage, v dc tube packing tape and reel packing 1 coil latching agq210 m 1h agq210 m 1hz 1.5 1.13 1.13 66.7 22.5 100 2.25 agq210 m 03 agq210 m 03z 3 2.25 2.25 33.3 90 100 4.5 agq210 m 4h agq210 m 4hz 4.5 3.38 3.38 22.2 202.5 100 6.75 agq210 m 06 agq210 m 06z 6 4.5 4.5 16.7 360 100 9 agq210 m 09 agq210 m 09z 9 6.75 6.75 11.1 810 100 13.5 agq210 m 12 agq210 m 12z 12 9 9 8.3 1,440 100 18 agq210 m 24 agq210 m 24z 24 18 18 5.0 4,800 120 36 dimensions 1. pc board terminal 10.60 0.3 .417 .012 0.40 0.1 .016 .004 2.20 0.15 .087 .006 2.20 0.15 .087 .006 3.20 0.15 .126 .006 3.50 0.3 .138 .012 5.20 0.2 .205 .008 7.20 0.3 .283 .012 0.20 0.1 .008 .004 5.08 0.15 .200 .006 pc board pattern tolerance: 0.1 .004 5.08 .200 2.20 .087 2.20 .087 3.20 .126 8-0.85 dia. 8-.033 dia. schematic (bottom view) single side stable (deenergized condition) 1 coil latching (reset condition) direction indication 4 3 2 1 5 6 7 8 direction indication 4 3 2 1 5 6 7 8 mm inch 2. surface-mount terminal 1) a type 10.60 0.3 .417 .012 0.40 0.1 .016 .004 max. 5.40 .213 8.40 0.3 .331 .012 3.20 0.15 .126 .006 2.20 0.15 .087 .006 2.20 0.15 .087 .006 7.20 0.3 .283 .012 0.20 0.1 .008 .004 5.08 0.15 .200 .006 suggested mounting pad single side stable/ 1 coil latching 3.20 .126 2.20 .087 2.20 .087 0.80 .031 2.66 .105 6.74 .265 1) s type 10.60 0.3 .417 .012 max. 5.40 .213 0.40 0.1 .016 .004 3.20 0.15 .126 .006 2.20 0.15 .087 .006 2.20 0.15 .087 .006 7.20 0.3 .283 .012 7.20 0.3 .283 .012 0.20 0.1 .008 .004 5.08 0.15 .200 .006 suggested mounting pad single side stable/ 1 coil latching tolerance: 0.1 .004 3.20 .126 2.20 .087 2.20 .087 0.80 .031 2.06 .081 6.14 .242 schematic (top view) single side stable (deenergized condition) 1 coil latcing (reset condition) direction indication 4 3 2 1 5 6 7 8 direction indication 4 3 2 1 5 6 7 8 reference data 1. max. switching capacity 2. life curve 30 100 contact voltage, v 1.0 0.3 dc resistive load ac resistive load switching current, a switching current, a no. of operations, 10 4 0.2 0.4 0.6 0.8 1.0 1.2 100 50 30 40 20 10 0 dc 30v resistive load ac 125v resistive load
gq 132 notes 1. coil operating power 1) as a general rule, only a pure dc pow- er supply should be used for the coil drive. 2) to ensure proper operation, the voltage applied to both terminals of the coil should be 5% (at 20 c 68 f ) the rated operating voltage of the coil. also, be aware that the pick-up and drop-out voltages will ?uctu- ate depending on the ambient tempera- ture and operating conditions. 3) the ripple factor for the voltage applied to the coil should be less than 5%. 4) for set and reset latching relays, the rated operating voltage should be applied to the coil for 10 ms or more. 2. coil connection when connecting coils, refer to the wiring diagram to prevent mis-operation or mal- function. 3. external magnetic ?eld since gq relays are highly sensitive po- larized relays, their characteristics will be affected by a strong external magnetic ?eld. avoid using the relay under that con- dition. 4. cleaning in automatic cleaning, cleaning with the boiling method is recommended. avoid ul- trasonic cleaning which subject the relay to high frequency vibrations. it may cause the contacts to stick. lt is recommended that a ?uorinated hy- drocarbon or other alcoholic solvent be used. 5. packing style 1) the relay is packed in a tube with the relay orientation mark on the left side, as shown in the ?gure below. 2) tape and reel packing (a type) (1)-1 tape dimensions mm inch (s type) (1)-2 tape dimensions (2) dimensions of plastic peel mm inch 6. automatic insertion to maintain the internal function of the re- lay, the chucking pressure should not ex- ceed the values below. chucking pressure in the direction a : 9.8 n {1 kgf} or less chucking pressure in the direction b : 9.8 n {1 kgf} or less chucking pressure in the direction c : 9.8 n {1 kgf} or less please chuck the portion. avoid chucking the center of the relay. in addition, excessive chucking pressure to the pinpoint of the relay should be also avoided. orientation (indicates pin no.1)stripe stopper (green) stopper (red) orientation (indicates pin no.1)stripe stopper (green) stopper (red) relay polarity bar (z type) tape coming out direction general tolerance 0.1 mm .004 inch 1.50 dia. .059 dia. 4.00 .157 0.40 .016 1.75 .069 2.00dia. .079dia. 2.0 .079 12.0 .472 9.0 .354 max. 6.55 .256 24.0 0.3 .945 .012 11.1 .437 11.5 .453 +0.1 0 +.003 .0 gq relays relay polarity bar (z type) tape coming out direction general tolerance 0.1 mm .004 inch 4.0 .157 0.40 .016 1.75 .069 2.00dia. .079dia. 2.0 .079 12.0 .472 7.8 .307 max. 6.55 .256 11.5 .453 1.50 dia. .059 dia. +0.1 0 +.003 .0 gq relays 11.1 .437 24.0 0.3 .945 .012 21 0.8 dia. .827 .031 dia. 13 0.2 dia. .512 .008 dia. 24.4 .961 +2 0 +.079 0 2.0 0.2 .079 .008 2.0 0.5 .079 .020 100 1 dia. 3.937 .039 dia. 330 2 dia. 12.992 .079 dia. a c b for cautions for use, see relay technical information (page 48 to 76). 9/1/2000 all rights reserved, ? copyright matsushita electric works, ltd. go to online catalog
|
